Change or rekey · Toronto
Lock Replacement & Upgrade
The century home's original mortise lock takes a key the size of a spoon, sticks in humid weather and has worn its strike to a groove.
In plain words
After a break-in or an attempt, the door tells a story, and the new hardware should answer it. Splintered wood around the strike means the jamb gave before the lock did, so the repair pairs a heavier deadbolt with a reinforced strike and 75 millimetre screws that reach the framing behind the jamb. A bent bolt or cracked housing is replaced with a graded deadbolt whose bolt has a hardened core. A knob lock that was bumped or forced is swapped for a set with better pins. The aim is a whole opening that resists force, not merely a shinier lock.
How the visit goesThe lever on the side door droops toward the floor and rattles in your hand. The latch no longer springs back on its own, so the door drifts open behind you unless you pull it shut and check it twice.
Lock Replacement & Upgrade
How the visit goes
How the old lock behaves in use
The locksmith works the existing hardware the way you do every day and watches for the tell-tale signs. A key that must be lifted or wiggled points to worn pins or a worn key. A knob that turns too far, or a lever that droops, suggests a tired spindle or spring. A latch that stays retracted, or a bolt that stops short, can be internal wear or something outside the lock altogether. Doing this with the door open first, then closed, separates faults inside the mechanism from faults in the fit of the door, and that distinction decides whether new hardware is the answer or part of the answer.
Mounting the cylinder and the interior side
The exterior housing goes on with its tailpiece passing through the slot in the bolt, oriented as the maker specifies so the keyway sits upright. The interior thumb-turn or rose is offered up and the two long mounting screws are drawn down evenly by hand until firm, not crushed; zinc housings distort and threads strip under a drill, and an over-tight rose makes a lever heavy forever. On thick doors, extension kits bring screws and spindle to length. A knob or lever set adds the latch spindle and the spring cage, and the handle is checked to return crisply to level before the trim is snugged.
The rental paperwork, quietly sorted
If the door belongs to a rental unit, the visit finishes with the keys in the right hands. When a landlord orders the change, giving the tenant a full set of new keys is standard practice. When a tenant orders it with the landlord's consent, a key for the landlord is cut alongside the household's and the consent is noted. The locksmith can leave a short written record of the hardware fitted and the keys issued for the property file, so both sides know what is on the door and nobody is surprised at the next inspection or move-out.
Lock Replacement & Upgrade
In the van
Manufacturer-approved cylinder lubricant
Chisels, mallet and hand screwdrivers
Boring jig and hole saws
Filler plates and thick-door extension kits
Knob or lever entry set
Lock Replacement & Upgrade
What affects the quote
Older and mortise hardware
Servicing an original mortise case, sourcing a compatible cylinder or fitting a conversion plate on a century door involves more assessment and fitting time than a standard cylindrical replacement.
Changes to the door preparation
Adjusting a strike mortise is minor; boring a new hole for a deadbolt, fitting a filler plate over an old mortise pocket or adapting a thick door with extension kits is quoted as its own item.
Type of lock
A knob set, a lever, a deadbolt, a full handleset with deadbolt above, a patio door lock and a keypad or smart deadbolt each carry a different hardware cost and take different time to fit.
What to have ready
- Do you want every exterior door to open with one key?
- Is the problem wear, damage, looks, a change of function or too many keys?
- Do you own the home, or rent it with the landlord's agreement to change locks?
Lock Replacement & Upgrade: questions
QuestionsCan you match the new lock to my other door hardware?
Yes. Manufacturers make deadbolts, handlesets, knobs and levers in matching finishes and styles, so a replacement deadbolt can sit above your existing handle without looking like an afterthought. Bring or photograph the hardware you want to match, including the interior side, and note whether it is a warm brass, a satin nickel, an oil-rubbed bronze or a matte black. Where an exact match is not made, the locksmith suggests the closest family.
I have just bought a house. What should I do about the locks?
Assume that copies of the old keys exist somewhere and act on the day you take possession. Walk every exterior door with the locksmith, keep hardware that is sound and have it rekeyed to a new key, replace hardware that is worn or too light, and add a deadbolt to any door that lacks one. Ask for everything to be keyed alike so you leave with one key and a known number of copies.
Can the same visit replace locks on more than one door, or does each door need its own appointment?
One visit usually covers every door on the job. The locksmith brings a range of cylinders and strikes, measures each door's backset and bore, and works through the list in order, front entrance first if a key change matters most there. Having a rough list ready, which doors, and whether they should end up on one key or several, lets the locksmith plan hardware before arriving rather than working it out door by door on site.
Related services
- Deadbolt InstallationThe front door has a handsome lever and a keyed knob, and that is all.
- Vintage Mortise Lock ServiceThe interior bedroom doors on the second floor have the original mortise latches, and none of them close any more.
- Smart Lock InstallationThe rental turns over every few months and each time you drive across town to swap keys, then wonder whether copies were made.